Nov 162011

Every Room Must be Fit for Purpose-Part C

The National Building Regulations (NBR) are not prescriptive when it comes to the size of rooms and buildings. However it is vital that the size of any room or space is fit for the purpose for which it was intended.

In the case of a really small house – or “dwelling unit” – the floor area of the entire building must be able to accommodate a “habitable” room as well as a separate room with toilet facilities. This is more for sanitary reasons than for comfort, and it makes perfect sense.

That’s about it, though the SANS deemed-to-satisfy requirements do give a little more guidance.

The updated requirements, published by the SABS in October 2010, were compiled with the assistance of the South African Institution of Civil Engineering. You can buy them from the SABS, either from one of their offices, or online.

What SANS 10400-C Covers

In essence the section on Part C, Dimensions in the Code of practice for the application of the National Building Regulations simply establishes the requirements for plan size dimensions as well as room heights and overall floor areas. It’s that simple.


The National Building Regulations and Standards Act has a glossary of terms; however there are additional terms that are defined in the various parts of the SABS codes of practice.  In Part C, there is a new definition of category 1 buildings. These are specifically buildings that are classified as:

  1. Places of instruction (A3)
  2. Buildings used for worship (A4)
  3. Small shops (F2)
  4. Offices, as well as banks, consulting rooms and similar (G1)
  5. Dormitories where a groups of people are accommodated in one room (H2)
  6. Domestic residences with two or more dwelling units on a single plot (H3)
  7. Dwelling houses, which may or may not include a garage and/or outbuildings (H4)

But in addition to the classification there are several other parameters:

  • There must not be a basement in the building
  • The maximum length between walls or “members” that provide lateral support is 6 m
  • The floor area in the building may not exceed 80 square metres.

There are certain requirements and limitations that are imposed on category 1 buildings by other parts of SANS 10400. For instance, in terms of Part T, Fire Protection, they are restricted to one storey. The maximum number of people allowed in category 1 buildings is also regulated.

Supposedly this means that if a house, church, office, shop etc has a basement or is double storey, it is not classified category 1, and a different code of practice will apply.

Dimensions of Plans

When you see dimensions on plans, you will know that these are the horizontal dimensions between UNPLASTERED wall surfaces. Of course once you plaster a wall and re-measure it, the distance between the two walls will be slightly less, since there will usually be at least 10 mm of plaster on the wall (though no one coat should be thicker than 15 mm) – and up to 30 mm if three coats of 10 mm-thick plaster are applied.

The Height of Rooms

If you’re a keen camper, you may not mind bending down in your temporary canvas home. But homes and other buildings have to be able to accommodate people standing up! Very few people are taller than 1,8 m (most are shorter), and so room heights generally are set at between 2,1 m and 2,4 m. This doesn’t, however, prevent designers making ceilings higher than this, even though it does increase building costs.

Minimum heights specified relate to different rooms in homes and other buildings:

Bedrooms. 2,4 m above a floor area of at least 6 sq m with a clear
height of at least 1,8 m at any point that is more than
0,75 m from the edge of the floor space.
Any other habitable rooms in dwelling houses/units. 2,4 m above a minimum of 70% of the floor area, and
not less than 2,1 m above the remaining floor area.
All other habitable rooms. 2,4 m.
Passages and entrance halls. 2,1 m.
Bathrooms, shower rooms, laundries and toilets. 2,1 m above any area where a person would normally
stand upright.
Open mezzanine floor with an area no more than
25% of the area of floor immediately below it
2,1 m above and below the mezzanine floor.

Note that this specification has not changed since 1990 – so the existing table in the free downloadable version of SANS 10400 applies.

When ascertaining the height of a room, the minimum dimension allowed is measured from the top of the finished floor to either:

  1. the underside of the ceiling,
  2. the underside of the roof covering (if there isn’t a ceiling), or
  3. the underside of any structural element (member) that is below the ceiling or roof and is larger than 30% of the plan area of the room. In addition, if there is a structural element projecting below ceiling or roof covering level, the height of the projection may not be less than 2,1 m

How to interpret the dimensions relating to minimum floor to ceiling height

In the top section of the drawing, two levels are indicated. Normally the height would be taken at level 2, but if the total plan size of the shaded areas in the bottom part of the drawing exceed 30% of the total area of the room, the ceiling height should be measured to the first level indicated.

Floor Areas for Buildings

Having said that the floor area of a small size home must be large enough to be habitable, plus must accommodate a separate toilet, there are other specifications in the regulations to consider. So while the minimum specifications are pretty tiny, they are not quite as small as you might be imagining.

For instance the regulations state that the floor of any permanent building that is used as a “dwelling house” must be no less than 30 m². Permanent category 1 building may be smaller, 27 m²; and temporary buildings can be as small as 15 m². So while a bedroom can legally be as small as 6 m² (providing no wall is shorter than 2 m) it won’t be sufficient to add on a bathroom and loo and claim that it is a house!

There are also minimum specifications in terms of the floor area allowed for a certain number of people using a room or building at any one time. This is based on the dimensions shown on the plans, but excluding the area that is taken by built-in cupboards, cabinets and so on (see drawings below).


How to measure floor plan areas

These references are specifically in terms of change rooms and dining rooms, and so relate not only to private dwellings, but to hostels and other establishments. If one to 15 people are going to be using a dining room, the minimum allowable area is 0,8 m² per person, but the room must still be at least 6 m² in size.

Not much space to party!

Main Photograph top © Janek Szymanowski



Public Safety

  125 Responses to “Dimensions”

Comments (124) Pingbacks (1)
  1. Hi there. When home are advertised they refer to the square meter size. Does this typically include the garage/s as well?

  2. Hi. Where is the mean height of a stand? The stand is in a estate.

  3. Hi . Do I need approval to put up a 40m2 nutec house on my property to house my parents?

  4. can you please advice if is it legal to build a double story flat/house with a balcony facing my naibour and within how many meters you allowed to build such closer/far from the naibour’s wall

    • If it is within the building line the is relevant to your property. Your title deed and the zoning regs will determine distance.

  5. Good day

    Could you please let me know what the min stand size should be to build 4x80sq townhouses (flats) should be? It’s would be a double story so 2 first floor and 2 the second floor..

  6. What is the maximum building height for a log house on mountainside??

  7. Good day

    Can you tell me what maximum size of a granny flat is allowed, and can i make a double story granny flat

    • Your local authority will advise – and they are the people who will need to approve your plans. This isn’t covered by the NBR as such.

    • Our local authority e.g. adds a R25 thousand “levy” if such granny flat has a kitchenette with a zink in it. Enquire about that from the building inspector at your local municipality. A zink in a kitchenette implies a “separate” dwelling so to speak. Something you “can rent out” I was told.

  8. Can you please advice the ratio for toilets in a home

  9. Can you tell me what is the required/norm lip from door frame to floor. Not sure if that is making sense – door frame seems to be too high and when they put the tiles in, there might still be a 20mm gap leading outside – should it not be flush with the floor?

  10. Is 5metres x 5 metres big enough for a double garage in the Western Cape ? does it comply with the latest building regulations ?

  11. Good day,

    Can you please advise on the legal requirement around having a fire hose reel inside an office.

    History: It was part of an open space, and the demand for office space increased. The space was converted into an office with the fire hose reel staying with the original design, now inside the new office.

    I can not find any requirements that should be adhered to, except for notices & signs, inspection and clear from obstruction and lockable doors ect….

    Can you please direct me to the requirements if needed.


    • Jaco, Part W: Fire Installation of SANS 10400 specifies how fire fighting equipment – including fire hose reels should be installed. Part T: Fire Protection specifies the number of hose reels required as well as where they should be installed. e.g. the reel must be installed so that the end of the hose will reach any point in the area to be protected. Also, you need one hose reel for every 500 m2 or part thereof of floor area in any storey. In addition, hose reels installed in buildings must comply with the requirements of SANS 543; should be installed in accordance with SANS 10105-1 and SANS 10400-W; and must be maintained in accordance with the requirements in SANS 1475-2.

  12. What are the minimum sizes for bathrooms, bedrooms and kitchens? Please need help urgently.

  13. Hi,
    where am I able to find plaster thickness tolerances and room size/dimension tolerances?


  14. Hi

    Please I need your advise on the standard sizes and measurement of the doors in South Africa?
    I want to import steel doors and below is some of the sizes and measurement

    Steel board thickness to be 0.3/0.7mm for 50mm door,. And i0.4/1.0mm for 70mm door,

    Please advise me the require sizes.


    • Clinton I suggest you contact the SABS because it isn’t just sizes – there are a lot of other specifications that need to be complied with in order for doors to be SABS compliant.

 Leave a Reply


(required but will remain confidential and not be published)

© 2012-2017 SANS 10400 • © Notice Sitemap • Contact Us • Terms & Conditions Suffusion theme by Sayontan Sinha